Bowen Built LLC

Bowen Built LLC Partnering with only the best companies!

Former 17 yr Senior master Ford tech, I do everything from full engine builds, supercharger systems, full suspension setups, exhaust, transmission repair, electrical, drivability diagnosis and so much more.

Pair of 08 GT500's 😍 love it when I have two of the same cars with inverse paint jobs!
05/04/2026

Pair of 08 GT500's 😍 love it when I have two of the same cars with inverse paint jobs!

This 1970 Mustang had to go under the knife and have the strut towers replaced and a number of repairs. Then came in to ...
05/04/2026

This 1970 Mustang had to go under the knife and have the strut towers replaced and a number of repairs. Then came in to have the suspension setup correct and dial in the alignment. Quite a bit of adjustment needed as seen from the before side shot! Everything came out really well and the car tracks really nice and steers smooth!

This GT500 came in for a few rear suspension additions. stop the hop kit with spherical LCA bushings. Good way to keep ...
05/04/2026

This GT500 came in for a few rear suspension additions. stop the hop kit with spherical LCA bushings. Good way to keep that rear suspension lined up when getting deep into the throttle! Dialed in the alignment and sent her home. Sounds like she may be back later this year for a header install👍

Quick AirLift airbag kit install on the Ram SRO! Just to help out when towing the toys👊
05/04/2026

Quick AirLift airbag kit install on the Ram SRO! Just to help out when towing the toys👊

This SN95 turbo car was having an issue staying cool when idling and found the stock fan just didn't have the CFM to kee...
05/04/2026

This SN95 turbo car was having an issue staying cool when idling and found the stock fan just didn't have the CFM to keep up! This dual fan shroud is exactly what she needed. Idle temps at 180 deg and quieter than the stock single fan! This fan shroud doesn't fit with the stock ABS location. Due to the fact this car is a pretty dedicated race car the client opted to have the stock brake lines removed and we installed a full line kit with rear brake adjustable proportioning valve. To top it off I added a manual override switch for the fans to run them in the pits and also made a mount for the Holley Terminator screen.
She is off to the Holley wizard Steven Kiehne for tuning!

Roush Motorsports is ready to go hurt some feelings this season! Going to be a great summer at Road America, Holley Ford...
04/27/2026

Roush Motorsports is ready to go hurt some feelings this season! Going to be a great summer at Road America, Holley Ford Fest and Indianapolis motor speedway!!

This has been a huge learning curve all around...but so worth the outcome! I have always been disappointed with driveabi...
04/22/2026

This has been a huge learning curve all around...but so worth the outcome! I have always been disappointed with driveability and throttle control with KB superchargers. From horrible dashpot to rolling throttles and surging!

With some help from really smart people, The idea became a viable option!! This Carbon Fiber, 3D printed spacer plate allows for installation of a Ford Racing GT500 throttle body! A custom made intake tube with MAF location and a spectacular tune from Casey Wittmer has made this into one smooth criminal👊 from cold starts, parking lot creeping, 30mph cruising to blowing the door off the car next to you...this thing is DIALED!

The added bonus is the heat sink this plate provides the throttle body stays much cooler which will greatly help with longevity and consistency with the electronic throttle control. Huge thanks to Jacobson powder coating and welding for the quick turnaround on getting the intake tube looking mint with the satin black!

Well the '67 finally went home🤘 wish I could have gotten some video on this one but tough to do in the winter. This one ...
02/07/2026

Well the '67 finally went home🤘 wish I could have gotten some video on this one but tough to do in the winter. This one came in as a half built engine and a few boxes of parts and bags of bolts (mostly labeled at least). A project that started a few years back but was never completed.
Starting from the middle isn't always the easiest but I think it all worked out in the end! A fully built C4 trans with TCI converter, 408 stroker engine and a crazy awesome full suspension under this thing! A great combination of modern meets Classic😍 glad the Bowen Built could get this project finished up and running for my client.

This 1967 Fastback is finally coming together! 408 stroker paired with a fully built C4🤘 this engine has had a rough lif...
01/14/2026

This 1967 Fastback is finally coming together! 408 stroker paired with a fully built C4🤘 this engine has had a rough life so far but hopefully a brighter future😁 stay tuned for some sound clips of this one.

Address

Chaska, MN

Telephone

+16123844448

Website

Alerts

Be the first to know and let us send you an email when Bowen Built LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category