KSV Looms

KSV Looms Your friendly neighborhood South Florida wiring plug 🔌
Motorsport-grade wiring components. Built on real loom building experience.🌴

08/14/2026

Stuart, FL
No HOA
No closing costs
Lots of connectors
www.ksvlooms.com
🌴

35lbs of DR25 heat shrink, Raychem molded boots, and ATUM/SCL headed to long time buyer and friend Jr Wiring Solutions 📦...
08/12/2026

35lbs of DR25 heat shrink, Raychem molded boots, and ATUM/SCL headed to long time buyer and friend Jr Wiring Solutions 📦🫡
🌴

08/10/2026

Almost time…
🌴

08/10/2026

Quick explanation of some MIL nutplate part numbers. Notably here if you are buying for size MS3470 shell size 24, make sure to get the one that ends in ‘B’ for narrow fl**ge. Also shell size 8 thru 22 is 4-40, size 24 is 6-32.
🌴

Connector kits, wire cut lengths, Techflex Insultherm, Raychem DR25. 📦🫡🌴
08/07/2026

Connector kits, wire cut lengths, Techflex Insultherm, Raychem DR25. 📦🫡
🌴

Bit of a variety pack headed out to someone who would like to remain nameless. 🤐🤐 DTM and DT kits with rubber boots, Bos...
08/07/2026

Bit of a variety pack headed out to someone who would like to remain nameless. 🤐🤐 DTM and DT kits with rubber boots, Bosch Kompact kits, Kapton, more OEM connector kits, etc. This particular buyer was referred over to me from the team at Motion Raceworks, and after a good 35 min phone conversation I got him pointed in the right direction for the project. I can’t stress the importance to get some guidance before you start buying parts if you are new to this stuff. 30 minutes on the phone can save you from buying the wrong parts, spending extra money, and lengthening the build time. 📦🫡
🌴

Did a reorganization of the place here this past weekend. Still feeling a little bit lost with everything moved around ...
08/06/2026

Did a reorganization of the place here this past weekend. Still feeling a little bit lost with everything moved around some, but new setup is much more efficient than previous. I really tried hard to get everything compact and close to the tables with enough room and not feel cramped, Having all my small individual components such as all the OEM housings, wire seals, terminals still within an arms reach and moving the Deutsch stuff directly behind the packing station is a huge improvement. Got some additional new stuff coming up soon that should also help me provide ya’ll a better buying experience all around. It’s been almost 1 year since the move to Stuart, FL from St Pete post hurricane Helene mess, and I’ve just about dug myself out of the massive hole I was in. For everyone that has purchased from me, liked, shared, etc and continued to support Teddy’s dream over here at KSV - Thank you ♥️🙏
🌴

A few MIL parts off to Jeff and team 511 Innovations 📦🫡🌴
08/05/2026

A few MIL parts off to Jeff and team 511 Innovations 📦🫡
🌴

DTM, DT kits along with some GT150 fluid and air temp off to Manuel Soler 📦🫡🌴
08/05/2026

DTM, DT kits along with some GT150 fluid and air temp off to Manuel Soler 📦🫡
🌴

Twisted Vinyl Co coming in clutch with another quick turnaround. ♥️ 🌴
08/05/2026

Twisted Vinyl Co coming in clutch with another quick turnaround. ♥️
🌴

Address

7932 SW Jack James Drive
Stuart, FL
34997

Telephone

+18887255711

Website

, , ,

Alerts

Be the first to know and let us send you an email when KSV Looms posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to KSV Looms:

Shortcuts

Share

Category