Encore Window Tinting & Paint Protection Film

Encore Window Tinting & Paint Protection Film Encore Window Tinting and Paint Protection Film - Window Tinting - Commercial, Residential and Automotive window tinting. Automotive Paint Protection film.

07/15/2026

The Slide Chomp PPF Method

In this clip, I’m using a method I call the “slide chomp” while working on a 2026 Tesla Model Y Performance front bumper.

This technique is all about how you hold the squeegee and the angle you use to push the edges down. Instead of just forcing the film into place, you want to guide the squeegee in a way that helps lock the edge down cleanly without creating unnecessary tension or damage.

Small changes in squeegee angle can make a big difference on bumper edges like this.

07/11/2026

Leave Extra PPF in the Recess

In this clip, I’m positioning the PPF on a Lotus Evora GT front bumper and making sure to leave a little extra material in the recess before squeegeeing it out.

That extra material is important because it lets the film lay into the recessed area without being under a bunch of tension. If you stretch the film too tight across areas like this, it may look good at first, but that tension can lead to lifting or failure over time.

A clean install is not just about getting the film down — it’s about setting it up to stay down.

07/08/2026

Squeegeeing PPF on a BMW M8 Bumper

Squeegeeing out sections of the BMW M8 front bumper while explaining what I’m doing along the way.

Bumpers like this have a lot going on, so it’s important to work each area with a plan instead of just pushing water around randomly. In this clip, I’m showing how I approach different sections of the bumper and work the PPF into place cleanly.

06/24/2026

Squeegeeing Matte PPF Looks So Satisfying

Squeegeeing matte-finish PPF onto the hood of a 2026 Ford Bronco.

This footage is sped up to 3.5x, and I removed everything except the actual squeegeeing. With the film stretched and positioned correctly, the material goes down incredibly cleanly.

A smooth installation starts long before you pick up the squeegee!

Check out the full install here:
https://youtu.be/ZaNdEYrwUOk

06/20/2026

3 Heat Sealing Tips For PPF 🔥

Working on the 2026 Mazda CX-90 fender and sharing three tips for heat sealing PPF edges. 🔥

✔️ Use the proper heat gun temperature.
✔️ Know how to push down edges that pop up after adding heat.
✔️ Avoid damaging neighboring pieces that line up with the panel you're currently sealing.

Heat sealing is one of the final steps of a PPF installation, but it's also one of the most important. Taking your time and paying attention to these details can make a big difference in how well the edges hold up over the years.

Watch full PPF tutorials on the ENCORE Window Tinting YouTube channel!
https://youtu.be/tKPSFAhDHKw

06/17/2026

PPF Fender Alignment Before You Start

Getting the alignment right before you start makes the whole install easier.

In this short, I show how I position the PPF on a fender and explain what needs to line up before making the first tack point. Once everything is aligned with the headlight and body lines, I lock it in and start the install.

Small adjustments at the beginning can make a huge difference later on.

06/03/2026

PPF Finger Won't Stay Down? Try This!

One of the most useful techniques for dealing with stubborn fingers in paint protection film is the Swipe & Hold Method.

Instead of letting the finger pop right back up, swipe the material into position and hold it momentarily to help the adhesive grab before continuing. This simple technique can make difficult areas much easier to install and help prevent unnecessary stretching or repositioning.

05/27/2026

BURPING AIR OUT OF PPF

In this PPF short I’m working on a full hood install on a Chevy Silverado. After the 4 corner tack, we’re dealing with deep recesses that trap air under the paint protection film. Before we can move on and start squeegeeing, I use a technique I call “burping the air out” to release the trapped air and help the film lay down properly.

Little techniques like this can make a huge difference on difficult full hood PPF installs with deep recessed areas.

Watch the full hood PPF tutorial:
https://youtu.be/NknGAghM1QQ

05/23/2026

Rinse Then Wrap The Edge

Working on the Lexus RX550 bumper and wrapping the PPF edges cleanly with a squeegee.

Before wrapping the edge, I rinse out the soapy slip solution with straight water. This helps reduce contamination and lets the edge tack down better before we finish wrapping it around the panel.

Small details like this can make a big difference in how clean and durable the finished install looks.

Watch full PPF tutorials on my YouTube channel:
https://youtu.be/bY8-WNQF4pM

05/20/2026

Snail Trails In PPF 🐌😬

Working on the Lexus RX550 bumper and talking about “snail trails” in paint protection film.

When water gets trapped under the PPF and starts drying, pushing that water bubble out can sometimes distort the adhesive underneath the film. Those small adhesive distortions are what installers call a “snail trail.”

In this short I explain what causes it and why you want to be careful when working out older drying water bubbles under the material.

Watch full PPF tutorials on my YouTube channel:
https://youtu.be/bY8-WNQF4pM

Address

1155 East Bianchi Road
Stockton, CA
95210

Opening Hours

Monday 9:30am - 5pm
Tuesday 9:30am - 5pm
Wednesday 9:30am - 5pm
Thursday 9:30am - 5pm
Friday 9:30am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Encore Window Tinting & Paint Protection Film posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Encore Window Tinting & Paint Protection Film:

Shortcuts

Share

Category