Kendrick Motorsports

Kendrick Motorsports Customization, repair, and restoration for automotive applications.

Had a 2018 Nissan rogue sport in for an oil change. Also the egt sensor.was bad, bc someone snapped it off. Swapped the ...
06/27/2023

Had a 2018 Nissan rogue sport in for an oil change. Also the egt sensor.was bad, bc someone snapped it off. Swapped the sensor but found more issues, like the frame is bent, and the Ac condenser is bent, plus the radiator support. Etc. Def be in for a followup.

Control box on the glastron was wasted. Found out the backing was also trashed so here we go
06/27/2023

Control box on the glastron was wasted. Found out the backing was also trashed so here we go

Summer is here and we're taking the boat out. The drivers floor dipped a bit so I cut the floor put. Factory floor is st...
06/27/2023

Summer is here and we're taking the boat out. The drivers floor dipped a bit so I cut the floor put. Factory floor is still there. Needs a complete redo but for this year I'll upgrade the fix. Cut a hole in the floor and have been fiberglassing ever since. New floor, New top floor. Also the controls were a bit soft.

Made a lot of progress. Front seat brackets are 90 percent done. Rear seats are modified and in, including 3 point belts...
11/07/2022

Made a lot of progress. Front seat brackets are 90 percent done. Rear seats are modified and in, including 3 point belts out of a 2017 gt.

Back to work on the 67. Passenger side seat braces are done, so doing driver side. Primer was delivered and tested the p...
10/14/2022

Back to work on the 67. Passenger side seat braces are done, so doing driver side. Primer was delivered and tested the paint so need to get on it. Also, they are straight, the shop that put the floor in didn't find it necessary to line up the passenger and driver seat pans apparently. I had to measure 100 times to make sure I wasn't crazy.

07/07/2022

Had excessive carbon on the rings making it run like crap. 70 psi combustion across the board. 45 mins of runtime and an extremely healthy dose of seafoam deep creep later. One giant stain on the cement and 120 psi of compression later we shall see if its remedied

Had pheasant chicks in the garage so was on a hiatus for a bit. Was able to get the cowl put on and welded in, got both ...
06/30/2022

Had pheasant chicks in the garage so was on a hiatus for a bit. Was able to get the cowl put on and welded in, got both new front fenders, cut the floor and started making the new seat risers for the mercedes seats.

67 was an automatic. I'm over it, getting a toploader so snagged the swing pedals and z bar from the blue car. Rebuildin...
05/13/2022

67 was an automatic. I'm over it, getting a toploader so snagged the swing pedals and z bar from the blue car. Rebuilding completely before Installing.

Factory fenders are trashed. Don't rivet aluminum to steel panels, it....it doesn't work. Ordered new replacements bc th...
05/13/2022

Factory fenders are trashed. Don't rivet aluminum to steel panels, it....it doesn't work. Ordered new replacements bc these are beat to crap. Also, Scott Drake doesn't have an antenna hole, so even less work to do.

Seat wiring is complete and tested. Heated, power seats are all working now. So much for needing a brain box. Had to cut...
04/27/2022

Seat wiring is complete and tested. Heated, power seats are all working now. So much for needing a brain box. Had to cut the trim and insert a new switch. Still needs cleaned up but it'll do. Still need to weld in floor supports yet.

Happy national mustang day! We have a few in the family.My 88 LX (fire)My 84 GT (sold)My 67 coupeMy other 67 coupeMy bro...
04/17/2022

Happy national mustang day! We have a few in the family.
My 88 LX (fire)
My 84 GT (sold)
My 67 coupe
My other 67 coupe
My brother's 92
(Not pictured, my dads 69 Mach, My moms 04 Mach 1)

Gutted the entire interior, had to cut the seat pans out to fit newer seats in. Will reinforce and tie into the subframe...
04/11/2022

Gutted the entire interior, had to cut the seat pans out to fit newer seats in. Will reinforce and tie into the subframe connectors anyway. Seats were grabbed out of a 2013ish mercedes c250. Only like 6 motors in the drivers seat so had to remap all the wiring, bypassing mercedes brain boxes and door switches. Working on modifying factory seats with a different model to make the switches all work and heated seats. Once these are done can line the interior and move to the quarters.

Address

Omaha, NE
68137

Telephone

+14024024022

Website

Alerts

Be the first to know and let us send you an email when Kendrick Motorsports posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category