DECOMA Motorsports

DECOMA Motorsports DECOMA Motorsports is Southern California’s premier off-road vehicle fabrication shop.

We offer a wide variety of services ranging from lift kits, roll cages, long travel kit installation, suspension components, and welding & fabrication of all kinds.

Stainless header back system for the raptor . Utilizing an X pipe with two mufflers.
11/18/2021

Stainless header back system for the raptor . Utilizing an X pipe with two mufflers.

Some 1/4” hot roll open corner fatties from this afternoon.
11/13/2021

Some 1/4” hot roll open corner fatties from this afternoon.

Some stainless tigz from today on a custom header back exhaust system.
11/11/2021

Some stainless tigz from today on a custom header back exhaust system.

A few small upgrades/ changes and a little bit of prep and this thing is ready for testing in Barstow this Saturday. ...
10/29/2021

A few small upgrades/ changes and a little bit of prep and this thing is ready for testing in Barstow this Saturday.

Transmission crossmember I built today for the Raptor prerunner. The factory transmission crossmembers on these trucks ...
10/27/2021

Transmission crossmember I built today for the Raptor prerunner. The factory transmission crossmembers on these trucks hang below the frame becoming a spot for rocks to get hung up. The new design keeps it tucked up flush with the bottom of the frame rail. Swipe to the end to see the old crossmember…

Spent the last few weeks getting this Tundra dialed in for . Did a full front end prep, sandblast and on the kit, new ...
10/23/2021

Spent the last few weeks getting this Tundra dialed in for . Did a full front end prep, sandblast and on the kit, new front clip and bedsides, new front bumper, new exhaust with mufflers, mounted both front on sliders, light rear prep, and steel it on lower links. Need to finish up some wiring and this truck will be dialed for the season.

Realized I never posted any finished pictures of the F-350 prerunner we built for so here’s a few from when it rolled o...
10/20/2021

Realized I never posted any finished pictures of the F-350 prerunner we built for so here’s a few from when it rolled out of the shop. I think Chris is getting pretty close on the plumbing and wiring so hope to see it in the desert some time this season.

Realized I never posted any finished pictures of the F-350 prerunner I built for so here’s a few from when it left the ...
10/20/2021

Realized I never posted any finished pictures of the F-350 prerunner I built for so here’s a few from when it left the shop. I think Chris is pretty close on the plumbing and wiring so hope to see this thing out in the desert some time this season.

Clean and functional front bumper on this tundra today. Overlapping skid plates wrap all the way down to protect the oil...
10/19/2021

Clean and functional front bumper on this tundra today. Overlapping skid plates wrap all the way down to protect the oil pan. Topped off with 6 lights.

Haven’t posted a lot lately but it’s not for lack of being busy! Been doing a bunch of not so exciting prep work getting...
10/12/2021

Haven’t posted a lot lately but it’s not for lack of being busy! Been doing a bunch of not so exciting prep work getting trucks ready for the upcoming desert season. Just finished up the front end prep on tundra. Kit went off to sand blast and came back and got and all new heims and uniballs.

Latest full build to roll out of the shop. This one got everything. Full back half with custom links, 4.0 motor swap wit...
09/23/2021

Latest full build to roll out of the shop. This one got everything. Full back half with custom links, 4.0 motor swap with full manual c4 trans, new engine cage and re worked beam kit, new swing steering system, full stainless tig welded exhaust, seats and steering wheel, dash, radio and intercom, all new plumbing, and shocks coil-overs and bypass on all 4 corners. #1450

Quick little project from last week. Finished out the cage in this cool little Baja bug. Customer brought me the car wit...
08/24/2021

Quick little project from last week. Finished out the cage in this cool little Baja bug. Customer brought me the car with an existing half cage and I completed it from the b pillar foreword.

Address

25941 Frampton Avenue
Harbor City, CA
90710

Opening Hours

Monday 9am - 4pm
Tuesday 9am - 4pm
Wednesday 9am - 4pm
Thursday 9am - 4pm
Friday 9am - 4pm

Telephone

+13104180258

Website

Alerts

Be the first to know and let us send you an email when DECOMA Motorsports posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to DECOMA Motorsports:

Shortcuts

Share

Category