Get Rowdy Performance

Get Rowdy Performance Coyote / Modular Ford Specialist. Aftermarket part installs from simple bolt ons to big power builds.

This Whipple gen2 coyote mustang came in for a set of Boundary Pump Division billet oil pump gears and crank sprocket. A...
07/14/2026

This Whipple gen2 coyote mustang came in for a set of Boundary Pump Division billet oil pump gears and crank sprocket. Along with that we did all new timing cover / valve cover gaskets from Ford Motor Company, Automotive Racing Products Inc. balancer bolt, 3” o/r pipes for the Stainless Works longtubes, ZPE GripTec supercharger pulley, fresh Motorcraft 5w-50 oil change / filter, and finished it off with a new belt and a set of Injector Dynamics 1300cc injectors!
—
Shoot us a dm for any and all of your coyote / modular ford mustang & f-150 needs!
—

This Gen 1 got an overhaul that was much needed! What’s on the car:BMR Suspension springs, control arms, panhard bar, et...
07/06/2026

This Gen 1 got an overhaul that was much needed!

What’s on the car:
BMR Suspension springs, control arms, panhard bar, etc
𝐒𝐓𝐑𝐀𝐍𝐆𝐄 𝐄𝐍𝐆𝐈𝐍𝐄𝐄𝐑𝐈𝐍𝐆 shocks / struts
McLeod Racing Street Extreme Clutch / Flywheel / S.S line
MGW Shifters Shifter / Cylindrical K**b
Ford Racing 1 piece driveshaft
SVE remote clutch reservoir
Automotive Racing Products Inc. flywheel bolts
New Oem rear main seal, slave cylinder
—
Shoot us a DM for all your coyote & modular ford needs!
—

This gen3 coyote s550 was brought in for some work. We got him setup with a set of Speed Engineering longtubes/xpipe and...
06/23/2026

This gen3 coyote s550 was brought in for some work. We got him setup with a set of Speed Engineering longtubes/xpipe and some BMR Suspension lowering springs and a “stop the hop” kit. Will be back in for a tune and cold air!
—

This Gen 2 came back in for another round of upgrades after breaking a stock axle. We installed a set of gt350 axles, th...
06/15/2026

This Gen 2 came back in for another round of upgrades after breaking a stock axle. We installed a set of gt350 axles, then he ordered a BMR IRS brace kit to go along with his stop the hop kit, and a set of BMR camber plates to get the alignment right up front! As well as wiring in his Mach 1 grill lights to the factory fog light harness!
—
Shoot us a DM for any and all of your Coyote & Modular ford needs!
—

This s197 came in non running and a mention that the abs module was running non stop. We found that the module had an in...
06/02/2026

This s197 came in non running and a mention that the abs module was running non stop. We found that the module had an internal short and melted the module and harness plug together. Shorting some wires together causing the car not to run. We decided it was best to do an ABS delete on this particular car so we chopped the harness plug off and terminated all the wires, cleaned up a few ecu grounds and this car fired right up. Then wrapped this job up with a abs delete kit.
—

Had this s550 in over the weekend for a set of long tube headers & and their x pipe kit. Fitment was great and paired w...
05/26/2026

Had this s550 in over the weekend for a set of long tube headers & and their x pipe kit. Fitment was great and paired well with the previously installed roush axle backs.
—

This super clean Platinum came in for a set of longtube headers! We got him setup with a set of catted longtubes, and I...
05/02/2026

This super clean Platinum came in for a set of longtube headers! We got him setup with a set of catted longtubes, and I must say I think it paired very well with his existing DB Performance by Corsa cat back!
—
Shoot me a DM for any of your Coyote or Modular Ford needs!
—

Helped my boy over the weekend on getting a new set of headers installed on his truck. We fought a constant battle of i...
04/27/2026

Helped my boy over the weekend on getting a new set of headers installed on his truck. We fought a constant battle of issues with the previously installed set.

This time around we put on a set of catless longtube headers and a stock f150 catback.

I will be highly recommending these headers from now on.
—







—

We gave this gen3 coyote an attitude adjustment with a set of longtube headers and a exhaust! —Shoot us a dm for all y...
04/25/2026

We gave this gen3 coyote an attitude adjustment with a set of longtube headers and a exhaust!
—
Shoot us a dm for all your coyote and modular ford needs!
—

Another simple gen 1 coyote out the door. We woke this car up with a Boss 302 Manifold paired with a .maf cold air inta...
04/17/2026

Another simple gen 1 coyote out the door. We woke this car up with a Boss 302 Manifold paired with a .maf cold air intake and a 93 & e85 tune from ! We then gave this car the perfect stance with a set drag springs and an adjustable panhard bar to keep the rear end centered.

During tuning the stock clutch showed signs of failure at high rpm shifts. So up next it will be getting a new clutch, a MGW shifter and some more goodies!
—
For all your coyote & modular ford needs shoot us a dm. We can discuss your goals and get you on the right track with your build!
—

Address

Greensboro, NC

Website

Alerts

Be the first to know and let us send you an email when Get Rowdy Performance posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Get Rowdy Performance:

Shortcuts

Share

Category