Twisted Wrenches Automotive LLC

03/15/2020

Hey y’all ! We want to thank each and everyone that has supported us in this adventure, but it’s time for us to move onto another adventure in our life . So with that being said , we are officially closed and moved out of the shop . If anyone needs anything feel free to give us a call ! Thank you guys for an awesome year !

10/07/2019

Hey everybody, we have been super busy the last couple of weeks and have not been on social media much. We are super excited because we have a few old school cars in here this week. We have a 1980 trans am that is getting the motor rebuilt, engine bay cleaned up and new floor pans. We also have a 1977 corvette stingray that we are prepping to throw this freshly rebuilt 400 into. If you have an old school build that you’re trying to get finished up give us a holler!

05/23/2019

This little Subaru got buttoned up last night and is running great and ready to go again. Give us a holler if you need a little help getting your car, truck, or jeep back up to par!

05/22/2019

A little bit of boxer prep before we swap her out tomorrow.

05/19/2019

Over the last couple weeks, we have had the opportunity to work on a lot of cool vehicles and have also had the ability to get people back on the road and feeling comfortable with their vehicles again. Just remember, turning up the radio will not make the noise under your car go away. Trust us, we have tried!

04/10/2019

As we come into a new week, we wanted to thank everybody for the continued support! Last week we got a couple cat-back exhausts installed in a Hummer and a 350z, a new transmission in a ranger, a brake/rotor/caliper job on a Chevy 2500 and a few other smaller jobs that were knocked out. This morning we have a customer that had the hub unit go out on his F350, but luckily wasn't far from home and was going slow. His knuckle seal failed, which allowed the bearings to rust and seize up. When the bearings failed, the outer hub and half of the rotor separated from the knuckle and remained attached to the wheel. Keep an ear out for any squeaking or squealing in your front end, because when something this vital goes out, you could potentially lose your tire driving down the highway and might not be as lucky as this guy. Always better safe than sorry! But for better news, we finally got signs made and now we are visible from the road! Thanks again and be safe out there!

03/25/2019

Been a productive week! Started off with tracking down oil leaks, front to rear, doing an oil change and also flushed the transmission fluid on a 1992 BMW. Continued the build on the Hummer. Also replaced the rotors and brakes on a GMC truck.

03/09/2019

Ole Blue got a pretty good workout today! Took about 7,000 lbs to the yard this morning. This should be our last big trip out to the scrap yard, as we are almost done cleaning out the new shop! In the shop right now is a 1994 Chevy blazer getting both driver and passenger side doors replaced.

02/08/2019

We would like to thank everyone who has followed us so far. I know we have been kind of quiet for a little while, but with silence comes a lot of hard work behind the scenes! As of Monday, we have officially moved into our new shop and are devoted to fixing and upgrading your vehicles. So far this week, we have done ball joints and tie rods on a Silverado, a transmission swap on a 350z, a 6" lift installation on an XJ, and a few other quick ones here and there. As we are moving into the new shop, we are working on getting rid of what is left from the previous owner. We are having a shop sale this Saturday and Sunday to sell what's left so we can access the other two bays and get more work in. If you need any tools, engine blocks, chevy parts or anything in between, stop by and see what we've got! 2557 George Owen Rd, Fayetteville NC 28306

12/26/2018

We would like to wish all of our followers and customers a merry Christmas and a happy new year! Thank you for all your support! Be safe out there and shoot straight downrange.

Send a message to learn more

12/17/2018

When life gives you an Audi, take the engine out.

12/17/2018

We had a newer customer ask us why we always tag and not or or any other major tool suppliers. Our answer was: because milwaukee wall.