No Limit Engineering

No Limit Engineering NO LIMIT IS EAST TENNESSEE'S PREMIER HOT ROD SHOP.
(220)

06/02/2026

//ROLL CENTER//

In this video we discuss roll center for trucks. It’s a combination of center of gravity, weight, and lever distance that affect body roll and grip pushing tires into the ground. Everything is a balance. It’s a relationship with the roll center, center of gravity, and sway bars.

Battle in Bama recap.  Winner Winner. Three long days of racing at Talladega Super Speedway, with rain delays and some l...
05/31/2026

Battle in Bama recap.
Winner Winner. Three long days of racing at Talladega Super Speedway, with rain delays and some late event drama the No Limit crew emerged victorious. Chris Edens driving Bill Holt's No Limit equipped Patriot Blazer came out swinging. He ran a first position fast lap in round 1 and never looked back. Tylar Gibson ran hard all weekend in his Scout, and made an impressive final round Hail-Marry run for a close second. Kyle Cochran and his Track Hoe blazer swapped positions with Duke Roddy's Dyno65 in a battle for third where the drama held out to a final round re-run for Duke, but not enough to claim back third position.
The course was over a half mile long. For comparison, top time was (1) Kyle Mullaney, Telsa 3P, 27.222 (2) Ryan Tolleson, Supra, 27.449. Chris and Tyler were P3 and P4 overall respectively. Very fast.
Congrats to all of the competitors in all classes, there was some very fast and close racing. Thanks to Grip Autocross, Battle in Bama and Talladega Super Speedway for hosting the event. Hope to see you all next year.
Final Stats:
Chris Edens 27.470
Tyler Gison 27.659
Kyle Cochran 29.510
Duke Roddy 29.626

05/30/2026

Day two at Talladega.

Battle in Bama day 1. Wheather was a factor but we skirted the rain for six good runs. Bill Holt's Patriot Blazer with C...
05/29/2026

Battle in Bama day 1. Wheather was a factor but we skirted the rain for six good runs. Bill Holt's Patriot Blazer with Chris Edens driving stayed out front all day with a 28.401 clean. Chris ran several 28.1xx runs but clipped the same cone on each run. Tyler Gibson ran a very close second with a best run 28.446. Duke Roddy showed he is a threat with several solid 29 sec runs, posting a 29.626. Bobby Allen snuck into the fourth spot in his S10 with a 30.535. And Kyle Cockran and the Track How put up a best lap 30.865 while tuning. Tomorrow we run earlier so the weather should be less of a factor.

About to go green in Talladega. Some fast trucks here. Who will come out on top. NLE Patriot Blazer, the Trach Hoe, Tyle...
05/29/2026

About to go green in Talladega. Some fast trucks here. Who will come out on top. NLE Patriot Blazer, the Trach Hoe, Tyler's Scout, Duke Doddy, or someone else?

We are set up for Battle in Bama at the Talladega Superspeedway.Come by and see us.
05/28/2026

We are set up for Battle in Bama at the Talladega Superspeedway.
Come by and see us.

//MEMORIAL DAY// 🇺🇸From the No Limit team, today we honor and remember the brave men and women who gave everything for o...
05/25/2026

//MEMORIAL DAY// 🇺🇸

From the No Limit team, today we honor and remember the brave men and women who gave everything for our freedom.

Wishing everyone a safe and meaningful Memorial Day.

Nice build from Rutter's Rod Shop.
05/19/2026

Nice build from Rutter's Rod Shop.

//BORUFF'S F100//We spotted this F100 this past weekend at the show in Pigeon Forge. Looking good! The No Limit suspensi...
05/18/2026

//BORUFF'S F100//

We spotted this F100 this past weekend at the show in Pigeon Forge. Looking good! The No Limit suspension has this one sitting just right.

💻 nolimit.net/store
📲 865-940-1503

Address

1001 Epco Drive
Dandridge, TN
37725

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm

Telephone

+18659401503

Alerts

Be the first to know and let us send you an email when No Limit Engineering posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to No Limit Engineering:

Share