Maloof Racing Engines

Maloof Racing Engines Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Maloof Racing Engines, Automotive repair centre, 1316 Robertson Loop Rd, Clarkesville, GA.

Installing billet main caps in a Gen I Viper today. More pics later in the process
09/23/2021

Installing billet main caps in a Gen I Viper today. More pics later in the process

2017 Hemi 5.7 stroker shortblock ready to deliver. Manley crank and rods, Mahle piston with 1/1/2mm ring package, custom...
09/03/2021

2017 Hemi 5.7 stroker shortblock ready to deliver. Manley crank and rods, Mahle piston with 1/1/2mm ring package, custom ground cam, VVT delete, etc.

Almost ready to fire it off. Forged bottom end LS with ported TFS cathedral heads, Procharged with a custom intercooler ...
08/01/2021

Almost ready to fire it off. Forged bottom end LS with ported TFS cathedral heads, Procharged with a custom intercooler and mounts, plumbing etc by the team we have here now. Ricky Cooper, myself, and Kevin Baxter have worked tirelessly to complete this project. I have to brag on these guys. The work we have performed is flawless! Ricky Cooper Kevin Baxter

Sneak peek at the first build coming out of MRE since Ricky Cooper and I joined forces.
07/21/2021

Sneak peek at the first build coming out of MRE since Ricky Cooper and I joined forces.

07/07/2021

I’ve been quiet on here for a while, but no more! LOL

I’m proud to announce the merger of two long time friends. Ricky Cooper from Redline performance has joined me to create the ultimate team.

I’ve changed directions on a project and I’mPut my personal engine up for sale. 383 1pc roller block....virgin block (I ...
10/28/2020

I’ve changed directions on a project and I’m
Put my personal engine up for sale.

383 1pc roller block....virgin block (I looked nearly 2 years before I found a block I would build this out of) bored and honed with plates, align honed, and square decked to .005 in the hole.
S**t crank
S**t stroker 6” rods w/ 7/16 bolts
SRP 16cc dish pistons 9.8:1
Comp XE 236/242 hyd roller
Billet timing set
Engine quest vortec castings 2.02/1.6 valves, with bowl work, exhaust porting, 64cc
Erson/Scorpion rockers

Every part of this engine is new except the block.

This engine should make an easy 475hp, possibly more with an intake swap.

Buyer chooses valve covers and I’ll split the cost of them.

$5500

Another Viper heading to Texas. Thanks RS Motorsports!
08/27/2020

Another Viper heading to Texas. Thanks RS Motorsports!

6.0 LS basic rods and pistons for boost. .030 over with torque plate, 9.3 compression, LS3 823 castings, 90% throat, Fer...
04/17/2020

6.0 LS basic rods and pistons for boost. .030 over with torque plate, 9.3 compression, LS3 823 castings, 90% throat, Ferrea valves, mild bowl work and blending, 68cc, billet timing set. The customer is going for 650whp 03 1500 Chevy.

452 FE Ford. I don’t know how I get all the problem engines in my shop. This was built by a very reputable shop that “sp...
04/03/2020

452 FE Ford. I don’t know how I get all the problem engines in my shop. This was built by a very reputable shop that “specializes” in FE’s. It lasted 1500 miles and had very little oil pressure. It was a mess inside to say the least. I had to machine everything over again including torque plate honing the block, align honing mains, rebalanced the assembly including the clutch setup, resized the rods, etc. I thought I was ready to assemble and....wrong. The cam would not go in the new bearings. I ended up boring the cam tunnel in the block as well. TDC wasn’t correct on the balancer either. It was 2 re****ed. The heads were equally out of shape. There was a minimum of .010 runout, and some were much worse. The valves were just as warped too, probably from pounding on a non concentric seat. Needless to say it was quite a project to correct bad machine work.

Pump gas 421.....10.4 compression Mahle pistons, S**t crank and rods, hyd. roller 242/250 .605 lift, Pro-filer heads 2.0...
02/12/2020

Pump gas 421.....10.4 compression Mahle pistons, S**t crank and rods, hyd. roller 242/250 .605 lift, Pro-filer heads 2.08/1.6 valves 90% throat size, cut my own angles on the seats, hand blended bowls and short side, SV2 intake. This should make a very nice street engine!

Another Viper wrapped up. 4.150 stroke billet crank, Oliver rods, custom JE pistons I designed, T&D rockers. This engine...
08/26/2019

Another Viper wrapped up. 4.150 stroke billet crank, Oliver rods, custom JE pistons I designed, T&D rockers. This engine came from a reputable shop. It was a disaster! The line hone was way off, cylinders appeared to be finished without a torque plate (when I bolt one on to hone the cylinders the there were shadows), small end bushings in the rods were worn out, etc. The heads had to be completely gone through, the guides were worn out and a couple were broken off. The valve train geometry was not correct. The oil pump pickup was smashed against the pan as well. It takes so much extra time to correct problems when another shop cannot get things right!

Address

1316 Robertson Loop Rd
Clarkesville, GA
30523

Telephone

(706) 839-1550

Website

Alerts

Be the first to know and let us send you an email when Maloof Racing Engines posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category