EZ LSx

EZ LSx We help put the EZ in LSx swaps by addressing your high performance automotive electrical needs! The Gen 3 broke the barrier and raised the bar once again!

The original Gen 1 small block Chevy engine set the bar high for performance V8 engines for over a half century. It was a design that dominated most motorsports and saw minimal changes in it's 47 years on the production line. It seemed that the time proven standard was never going to change. In the early 90s GM introduced the Gen 2 small block known as the LT1. By most standards the Gen 2 engines

were a lackluster attempt to show change while trying to maintain a tie to the old standard. It seems that they tried to improve on what they had instead of thinking outside the box to come up with something entirely new and better, but they've finally done it! GM finally took a fresh approach the their engine design and outdid themselves in the process. The have evolved into a smooth running, fuel efficient engine that runs smoother than ever with more power per cubic inch. These engines have become the new go-to engine for everything from daily drivers and hot rods to off road trucks, race cars and even marine applications. This new breed of engine is referred to as the LS engine and is commonly designated the term LSx where X is the multitude of variables/options available. As with anything new the idea of an LS swap can seem intimidating and that's where we come in. We take the guess work out of wiring the engine by converting the OEM engine harness to an easy to work with Stand Alone harness or we can custom build your new harness from scratch. Out primary focus is on building GM Gen 3 car and truck Stand Alone harnesses, but we can also do Gen 4 and Gen 5 harness builds as well. Our team looks forward to working with you to develop the perfect harness for your next project. Let us show you how EZ it really is!

Just sayin' 🤷🏻‍♂️
04/12/2024

Just sayin' 🤷🏻‍♂️

One???? We have lots of those friends!!!! 😎🤘
03/12/2024

One???? We have lots of those friends!!!! 😎🤘

The new shop is finally starting to take shape and should be in full swing by Summer 2024!!!
01/24/2024

The new shop is finally starting to take shape and should be in full swing by Summer 2024!!!

THE EZ PDM addresses all of your Stand Alone harness power needs in one compact unit.*Built in 80A Maxi Fuse for complet...
12/25/2023

THE EZ PDM addresses all of your Stand Alone harness power needs in one compact unit.

*Built in 80A Maxi Fuse for complete system protection (no more need to worry about a fusible link)

*Three 15A and 20A constant power outputs for ECM memory, TCM memory and OBD II connector power

*Seven 10A and 15A switched power outputs for ECM, coils, injectors and sensors

*Built-in relay for 12V+ power to the fuel pump with 30A fuse protection

*Built-in relay for 12V+ power to the starter solenoid with 40A fuse protection

*Built-in 60A switched power relay

*LED indicators for each fuse light up showing any blown fuses at a glance

*Built-in 1K Ohm, ½ Watt resistor for your tachometer “pull up” signal

*6mm power input stud allows you to use the same ring terminal and protection boot that you already used for your alternator terminal

*Tool-free service lid mounting

*Operating temperature range -40 °F to +185 °F (-40 °C to +85 °C)

*IP64 (dust-proof/ protection against splashing water)

*Compact size 179 mm x 140 mm x 62 mm

*Simple and secure connection with TE Connectivity 32 Pin Leavyseal connector* (not included)

…and we saved the best for last! Our exclusive built-in dual function relay. In Gen 3 LS engine applications it is used to convert the brake pedal signal of a normally open switch to mimic the signal of a normally closed switch for torque converter lock up control. If Gen 4 LS engine applications it uses the Power Train control signal from the ECM to keep the TCM powered up throughout the shutdown process.

*TE Connectivity Mating Connector Part Numbers:
1-2208685-6 is UL rated to V-0 flame rating. 1-1564297-6 is not V-0 rated

Merry Christmas and Happy Holidays from our garage to yours!!!! 🌲
12/25/2023

Merry Christmas and Happy Holidays from our garage to yours!!!! 🌲

07/04/2022
It's time to put in another order for Hoodies. They're $50 each including shipping in the US. If you want one send us a ...
01/23/2022

It's time to put in another order for Hoodies. They're $50 each including shipping in the US. If you want one send us a message with your size and PayPal info to send you an invoice. We will be taking orders until Feb 14th 2022 😎🤘

Just like everything else in today's world there are shortages on the HP Tuners MPVI2+ units. We only received half of o...
01/21/2022

Just like everything else in today's world there are shortages on the HP Tuners MPVI2+ units. We only received half of our latest order and is already only a few left.$399.99 with free Priority Mail shipping in the US. We also offer credits $47.50 each

Address

501 Clinton Street
Bow, NH
03304

Website

Alerts

Be the first to know and let us send you an email when EZ LSx posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category