Snapy Tom's

Snapy Tom's Custom Engine's and Repairs

Started on a cool 64' Impala. Large transformation from the firewall forward so far. The customer has tons of parts alre...
05/30/2026

Started on a cool 64' Impala. Large transformation from the firewall forward so far. The customer has tons of parts already and I get the privilege to install them.

Time for new Kevlar bands. Tore down the 27' Roadster top half " hoghead." Then cut all the brass rivets and started soa...
03/10/2026

Time for new Kevlar bands. Tore down the 27' Roadster top half " hoghead." Then cut all the brass rivets and started soaking bands before assembly.

1927 Modle T 2-door. Had to pull the head off and grind the seats. Installed all new valves, springs, and keepers. Adjus...
03/10/2026

1927 Modle T 2-door. Had to pull the head off and grind the seats. Installed all new valves, springs, and keepers. Adjusted the valve clearances. Put it back together and filled fluids. Got engine started and found #2 not firing. Replaced coil box and all is good.

More progress on the old 59' Skyliner.
03/10/2026

More progress on the old 59' Skyliner.

Here we go again. Didn't take this one apart so it is a true basket case.
08/21/2025

Here we go again. Didn't take this one apart so it is a true basket case.

This was one sweet ride.ENJOY
08/14/2025

This was one sweet ride.
ENJOY

08/14/2025

IT'S ALIVE!!

Getting along good on the 49' chevy truck. DIY harness for LS swap are time consuming. Got the engine put in the frame ...
04/18/2025

Getting along good on the 49' chevy truck. DIY harness for LS swap are time consuming. Got the engine put in the frame rails and drilled the holes for new engine crossmember. Clearance the frame to get everything to fit. Next week installed the bellhousing and checked the hole is centered and parallel. Pulled bellhousing installed flywheel, pilot bearing,and clutch assy. Replaced bellhousing and measured the average finger depths. Installed the correct shims to adjust the hydraulic throwout bearing. Installed transmission and crossmember. Installed new driveshaft. Got all the wires hooked up to the computer to the DIY harness. Fabricated front and rear brake lines. I installed the pedal assy. Hung the master-booster combo and mounted the proportioning valve. Starting to take shape.

Finishing up the 63' impala frame. Installed 4 wheel disc brake conversion. Rear got all new parts in the housing. Insta...
04/18/2025

Finishing up the 63' impala frame. Installed 4 wheel disc brake conversion. Rear got all new parts in the housing. Installed front and rear brake lines and pressure and return fuel lines. Front got the upgraded power steering gearbox and linkage. 13" gold spoke wheels and tires. I took apart the stock 327ci. engine and cleaned up everything. Crank had to be polished and rods got resized with new bolts. Cam wasn't any good so we installed a performance cam and lifters. Took the cylinder apart and cleaned them up. Lapped the valves and up graded the seals. Had the valve covers sand blasted to add a little personal touch. (One of a kind!) Installed a clear cap on the distributor and made new custom set of wires to dress this little engine up for the shows to come. Bolted up old exhaust and had to wack off the rear to fit the new frame. This will be a show stopper!

Getting a good start on the LS swap. Got the new guages installed too.
02/19/2025

Getting a good start on the LS swap. Got the new guages installed too.

Address

820 Seiling Street
Alva, OK
73717

Opening Hours

Monday 8am - 5:30pm
Tuesday 8am - 5:30pm
Wednesday 8am - 5:30pm
Thursday 8am - 5:30pm
Friday 8am - 5:30pm

Telephone

+15803272700

Website

Alerts

Be the first to know and let us send you an email when Snapy Tom's posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Snapy Tom's:

Shortcuts

Share