KCG - Klazzik Car Garage

KCG - Klazzik Car Garage Kontaktinformation, kartor och vägbeskrivningar, kontaktformulär, öppettider, tjänster, betyg, foton, videor och meddelanden från KCG - Klazzik Car Garage, Bilar, Hössjö, Umeå.

Nu händer det lite i KCG garaget 🔥 coming soon!
06/02/2024

Nu händer det lite i KCG garaget 🔥 coming soon!

Alltid arbete i grottan, inte konstant med bilar utan nu ska en skylt upp utanför garaget (om vi får för hyresvärden😁 Ra...
18/11/2023

Alltid arbete i grottan, inte konstant med bilar utan nu ska en skylt upp utanför garaget (om vi får för hyresvärden😁 Rasmuuuus) haft lite dålig motivation med V8 skruvning sen vintern kom på besök men lite Nick's Garage & Engine Dyno på youtube gav tillbaka elden i själen 🔥🔥

Min -68 Dodge Coronet RT får dock vänta till våren innan den får mer kärlek ❤️ ha en fin lördag !!

28/02/2023

Epoxyprimer done ✅ 1 light coat 2 heavy coats 😁

Done and done, zinc plating by David at DM Classics🔥🔥💨Time to reinstall the front end 😁
27/02/2023

Done and done, zinc plating by David at DM Classics🔥🔥💨

Time to reinstall the front end 😁

Hey, I have power coated almost every thing on the front end except for the K-member and a few other things that didn't ...
22/02/2023

Hey, I have power coated almost every thing on the front end except for the K-member and a few other things that didn't fit in the oven.

Klazzik Car Garage wishes a Merry Christmas to all of you 🎄We will change up a gear in 2023 so stay tuned 🔥🎁 thanks for ...
24/12/2022

Klazzik Car Garage wishes a Merry Christmas to all of you 🎄

We will change up a gear in 2023 so stay tuned 🔥🎁

thanks for support through this year and we will hope for a healthier 2023 ❤️

As life hits you hard the only thing in life we got left is hope!! Put the future in the kids hands.He might get the Cor...
17/09/2022

As life hits you hard the only thing in life we got left is hope!! Put the future in the kids hands.

He might get the Coronet if he lucky 🔥🔥😁

As much as we do in the shop sometimes we find times to help others, a week or 2 ago we helped a new friend Lars-Gunnar ...
09/09/2022

As much as we do in the shop sometimes we find times to help others, a week or 2 ago we helped a new friend Lars-Gunnar with his -68 Cadillac (some issues with a broken neutral safety switch) a quick bypass and we was able to start her up 🔥🔥

And this week our trustworthy and longtime friend Anders visited with his friend Magnus and his -68 Plymouth Satellite, he had issues with the carb, model chinesium 😂 thought it run fat but it didn't, we had a squeek noise from the power steering belt, and it was a pulley issue so he will order the right to get the belt straight.🔥🔥

Part 3.A whole lot of rear end and housing work again, installed the brake line brass Y split and the brake line, then m...
09/04/2022

Part 3.

A whole lot of rear end and housing work again, installed the brake line brass Y split and the brake line, then my good friend installed the drive shafts after removing the old seals inside the housing.

As a little brake from the rear end and to get a little closer to final assembly I put some elbow grease work on the wheels for a little better finish.

And the D was painted on the rear end as it was in 1968, I'm not that in to the original stuff but I think it's a part of the cars soul to have the original markings.

For all the gaskets I got the tip from my friend that Loctite 3020 works the best, so after spraying em down and had em rest for a good 10-20 min they could be installed.

Next up is the 742 with the 3.23 open diff, we changed things up and my friend Kimpan helps med and thought me some importance about pre tension and the install of the new Auburn Pro Series and a new 3.73 gear ratio.

#8.75

Part 2 Improvised a paintbooth just to do a first try with a paint gun and it went great, good coverage, put down 3 laye...
08/04/2022

Part 2

Improvised a paintbooth just to do a first try with a paint gun and it went great, good coverage, put down 3 layers in total.

The paint I used was Tikkurila 50 semi gloss black.

Bought new U-bolts cause the old one was rusted solid.

The old wheel bearing seals and wheel bearing were leaking so a upgrade to green bearings non adjustible.

The bearings was a tight fit but my friend did an amazing work putting em on, and I put the retainers on place by heating them to about 400 Celsius.


#8/75

Part 1.So this is the full Journey of the rear end rebuild.We did a thuroug deep wash with degreeser and acid, disassemb...
08/04/2022

Part 1.

So this is the full Journey of the rear end rebuild.

We did a thuroug deep wash with degreeser and acid, disassembly of the rear end from the housing and the drive shafts, put down extra time on the rear end that I took to my dear friend Kimpan for a rebuild and upgrade.

Used the wire brush and flappydisc to clean the housing to bare metal.

Threw the brake shields in to the sandblaster with the rear end support (option).

Adress

Hössjö
Umeå
90586

Öppettider

Måndag 17:00 - 20:00
Tisdag 17:00 - 20:00
Onsdag 17:00 - 20:00
Torsdag 17:00 - 20:00
Fredag 17:00 - 20:00
Lördag 09:00 - 20:00
Söndag 09:00 - 20:00

Telefon

+46707269979

Webbplats

Aviseringar

Var den första att veta och låt oss skicka ett mail när KCG - Klazzik Car Garage postar nyheter och kampanjer. Din e-postadress kommer inte att användas för något annat ändamål, och du kan när som helst avbryta prenumerationen.

Kontakta Affären

Skicka ett meddelande till KCG - Klazzik Car Garage:

Genvägar

Dela

Typ