Steward Motors

Steward Motors Robert Steward QSM started Steward Motors in 1958. His son John Steward started his app in 1970 With our experience you want go wrong.

The services we provide are GENERAL REPAIRS- SERVICING ALL MAKES- WOF CARS AND BIKES- PRE PURCHASE CHECKS- WELDING- MODIFYING- TRAILER REPAIRS- MOWER AND MOTOR BIKE REPAIRS- ELECTRICAL REPAIRS AND BATTERIES- BABY SEAT ANCHOR POINTS.

This is a very tidy 1970 Holden Monaro I worked on last week to make it stop and drive well.
08/07/2023

This is a very tidy 1970 Holden Monaro I worked on last week to make it stop and drive well.

A nice example of GMC ute i made some large tail pipes on this week and a land rover i did a full brake rebuild on.
21/02/2023

A nice example of GMC ute i made some large tail pipes on this week and a land rover i did a full brake rebuild on.

Just a few cars i have been working on in the last month
25/05/2022

Just a few cars i have been working on in the last month

Did a bit of panel repair today on a mk1 es**rt as well as brake callipers rekit and new pistons etc. This car has not b...
08/07/2021

Did a bit of panel repair today on a mk1 es**rt as well as brake callipers rekit and new pistons etc. This car has not been used for years so it took a bit to get it to go and drive.

Hi just a few things i have been doing the last couple of week at the shop, i had to make a housing to fit a thermostat ...
22/11/2020

Hi just a few things i have been doing the last couple of week at the shop, i had to make a housing to fit a thermostat to this ford 1600 cross flow race engine which had a hand made over head cam box fitted to it around 40 years ago. But to make it better for road use it needed a thermostat . Also fitted and wired up a 2 speed wiper motor into a mk1 es**rt. I also had to fix a beach tractor that needed a new manifold and exhaust as it had broken off due to it beening paper thin from rust.

Just a update on what i have been working on lately. One was a xj6 jag which i had to get running correctly, fix the aut...
15/09/2020

Just a update on what i have been working on lately. One was a xj6 jag which i had to get running correctly, fix the auto problems and balance the carbs, tune etc, replace all the ball joints and adjust inner rack ends as one pulled off rack as customer was turn in his drive. He had just purchased the car from the south island and it had a new WOF?.
The last last week was a 1953 Riley which i had to repair all the brakes and remove play from all the brake and clutch linkages, was not the cleanest classic car i have worked on.

Well finally got the mk1 es**rt certified. Last job was this chev pickup, had to raise suspension as it was sitting on t...
18/02/2020

Well finally got the mk1 es**rt certified. Last job was this chev pickup, had to raise suspension as it was sitting on the bump stops, very hard riding. Repair all brakes so it would pass a roller brake test, repair faulty light circuit and make some new headlight adjuster. Fit new valve stem seals. Had to fit a new crank shaft pulley as it fell off, it was so worn out it could of coarse a bad accedent if it came off on the road and went through somebody's windscreen. Fit new differential pinion seal to stop oil leak and then it flue through its Wof.

Hi Every body, I have had some good projects in the last 6 months. I final got the Mk1 ford es**rt on the road. The engi...
25/04/2019

Hi Every body, I have had some good projects in the last 6 months.
I final got the Mk1 ford es**rt on the road. The engine supplied with the car had a oil pressure problem which added a lot more work.
I would like to let you know that i can not take any work on until after July the 14th

This weeks job was a Chevrolet C10 Truck which had oil leaks in the diff, auto trans and engine. This meant engine out t...
13/06/2018

This weeks job was a Chevrolet C10 Truck which had oil leaks in the diff, auto trans and engine. This meant engine out to replace head gaskets, sump gasket etc. replace drive shaft yoke and seal, pan gasket. replace diff pinion seal and cover gasket. Also repair brake balance problem which caused the truck to spin around when braking lightly in the wet.

Address

3/5 Manga Road
Silverdale
0932

Alerts

Be the first to know and let us send you an email when Steward Motors posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Steward Motors:

Share