Track 7 Technologies

19/01/2018

We are proud to announce our Mobile Oil Change Delivery service. It is a quick l**e & service station on wheels. We come to you and service your vehicle wherever its located, at any time that suits your schedule. We services all makes and models of cars.

Just send us a message with your vehicle details and we'll be glad to get you a quote with the right filters and specific grade of oil for your vehicle. Approve and we'll be on our way to sort you out at your convenient location.

whatsapp: 0208947814.

At your service.

01/11/2017

What's ACEA, what's API, and how do their specifications relate? Discover it here.

30/08/2017

08/08/2017

06/08/2017

Have you ever wondered what the meaning of numerous codes written on the sidewall of tires could be? These codes are meant to help you  buy...

06/08/2017

Have you ever wondered what the lights on your vehicle’s dashboard mean? Some are obvious, but others might have you flipping through the p...

28/07/2017

5 ESSENTIAL FACTS ABOUT MOTOR OIL

1 - Oil change

True or False: You have to change your oil every 10 000 KM?

FALSE: For years, the rule of thumb was to have your engine oil changed every 10 000 kilometers, but with synthetic oil you can go much further. Gradually, car manufacturers have been extending oil change intervals to 15 000 kilometers, then to 20 000 and now even to 30 000 kilometers.
2 - Labels

True or False: The W in 5W40 refers to ‘Weight’?

FALSE: The W refers to ‘Winter’. The viscosity of motor oil is subject to temperature change. A single viscosity rate only represents the flow of oil when heated, but what if you need to start your car on a cold winter morning? That’s when the multi-grading rating comes in the picture. The oil will flow more slowly, which is different to when it’s heated, so this viscosity rating is important too. The number before ‘W’ represents the viscosity at engine startup, while the number following the ‘W’ represents the viscosity during engine operation.
3 – Color of oil

True or False: When engine oil turns dark, it's dirty and should be changed?

FALSE: On the contrary! Detergent oil disperses tiny particles, which can result in engine sludge, and it holds them in suspension. This way these particles can’t build up and that’s why the oil will appear darker. Of course, oil is limited to how many of these suspended particles it can contain. It eventually needs to be changed when it becomes saturated. Change your oil as recommended by your car’s manufacturer as its color on the dipstick is by no means the right indicator for an oil change interval.
4 - Additives

True or False: Engine oil additives boost your engine’s performance?

FALSE: Oil additives give the lubricant its detergent properties that keep your engine free of sludge. They also include rust retardants to prevent corrosion and contain additives to protect metallic surfaces. They also improve the engine oil’s viscosity index being the range of temperatures under which it flows properly through the engine. Using the right engine oil for your vehicle does not only boost its performance, it will also prevent a necessary engine flush. Use product recommendation tools when looking for oil!

5 – Synthetic oil older cars

True or False: Synthetic oils will cause leaks in older cars?

True: The seals in engines of older cars (20 years or older) with high mileage may not be able to handle the detergent capacities of the additives in synthetic lubricants, which could cause leakages. For these vehicles it is recommended to follow the instructions and recommendations you find in the manual of your car. The oils to use in older cars are of the mineral type with additives which are adapted to adequately protect these engines in particular.

19/07/2017

Pico Technology has introduced a new test lead for ultrasonic parking sensors to its range of accessories. The two-meter long lead gives technicians the ability to prove the correct operation of ultrasonic parking sensors. By directly showing the

13/07/2017

AC System Maintenance: System flushing Nissens Technical Bulletin 0 By autotech-nic on July 7, 2017 Article To perform properly, the AC system must be clinically clean inside the loop. Refrigerant and lubricant working in high temperatures and pressures, as well as components with precise mechanisms...

24/06/2017

P0403 – Exhaust gas recirculation (EGR) -circuit malfunction



Trouble Code Fault Location Probable Cause
P0403 Exhaust gas recirculation (EGR) -circuit malfunction Wiring, EGR solenoid, ECM
What Does P0403 Mean?


When a gasoline or diesel-powered vehicle runs, the fuel in the cylinder along with the oxygen in the air burns extremely hot. The gases produced in the combustion chamber are expelled in the exhaust stroke and sent through the exhaust pipe, destined for the atmosphere.

Unfortunately, fuel in the cylinders doesn’t burn completely. The unburned fuel is carried along with the exhaust as it exits the engine. These hydrocarbons are a major component of vehicle emissions and contribute to environmental pollution that can cause smog and exacerbate breathing issues.

In addition to unburned hydrocarbons in the exhaust gases, a particularly harmful byproduct of excessive engine heat is NOx. It is produced in a narrow range of temperatures at the upper limit of engine combustion.

The exhaust gas recirculation (EGR) system was developed to address these issues. The EGR system reintroduces a portion of the engine’s exhaust gases back into the combustion process. This achieves two things: completely burning the hydrocarbons in the exhaust gas as well as diluting the air in the combustion chamber to reduce ignition temperatures.

An EGR solenoid is used to meter the exhaust gases that are reintroduced into the engine. It also prevents the EGR system from operating until the engine is at operating temperature, otherwise the engine will run rough on startup as it starves for oxygen-rich air.

The EGR solenoid is typically mounted on the intake manifold. It uses engine vacuum to operate the EGR valve, which opens and closes to allow the exhaust gases into the intake. It receives 12-volt power from the powertrain control module when operating conditions — engine running and battery voltage above 12 volts — are met.

If the EGR solenoid circuit is not in the expected state when commanded by the PCM, DTC P0403 is set in the PCM and the Check Engine light is illuminated.

Symptoms of P0403

Symptoms vary depending on the position of the EGR solenoid circuit during malfunction. Symptoms may include:

Check Engine light
Rough run or misfire on startup, smoothing out as engine warms up.
Rough run or misfire when engine hot, yet runs properly on startup.
Hesitation to accelerate
Stalling
Fuel smell from exhaust
Troubleshooting P0403

Defective EGR Solenoid

The EGR solenoid can fail internally, either by cracking, spring failure, or otherwise. Usually if the EGR solenoid fails, it can easily be determined by removing the EGR solenoid and blowing air through the vacuum connections. When the EGR solenoid is removed, apply 12-volt power and ground to the solenoid. The vacuum passages should not be free-flowing. If you can blow through the valve, there is an internal failure and the EGR solenoid should be replaced.

EGR solenoid internal

Another way to check for a failed EGR solenoid is to disconnect the vacuum hose to the EGR valve while the engine is running cold. There should not be a change in the engine operation. If there is, it indicates a problem with the solenoid.

Lack of Electrical Signal to EGR Solenoid

The EGR solenoid is actuated with a 12-volt power source, switching the solenoid from the “leaking” position to a closed position when power is present. DTC P0403 most commonly indicates an electrical issue with the solenoid or the electrical connections.

You can check the electrical connections using a 12-volt test light and a DVOM. You’ll also need a vehicle-specific wiring diagram for the EGR solenoid circuit.

Poor wiring connection

The problem could be as simple as a poor connection to the EGR solenoid. Check for bent or broken terminals in the connector, or moisture or corrosion that can inhibit communication. Repair any problems and ensure the connector is fully seated and locked.

Short to voltage

Disconnect the two-wire harness from the EGR solenoid. With the key in the on position, connect one lead of the 12V test light to the negative battery terminal and probe the control circuit wire in the connector. If the tester lights up, there is a short to voltage on the control circuit. Trace the wire back to the PCM, checking for breaks, rubs, or corrosion on the wire that connect the circuit to power. Repair and retest.

If a short to voltage is present without a wiring problem, it’s possible the PCM has an inernal failure. Replace with a known good unit and retest.

Short to ground

Disconnect the control circuit from the EGR solenoid and the PCM. Test the control circuit using your DVOM, measuring resistance. If you have below 100 Ohms, there is a short to ground on the circuit. Trace the circuit for breaks or corrosion and repair.

Restriction in EGR Valve

The EGR valve operates by vacuum to open and close, allowing the exhaust gases to pass through. Restrictions can occur from carbon buildup especially, which is most notable in diesel engine applications. The restriction can either prevent the EGR valve from opening or, more commonly, restrict the valve from closing completely.

egr valve

Remove the EGR valve to inspect for an obstruction. Some carbon buildup is normal but should not prevent moving parts from seating when fully closed. If there is buildup, clean it completely to ensure smooth movement, then reinstall.

EGR Valve Operation

With the engine off, apply a hand-pump vacuum tester to the EGR valve vacuum supply port. Build vacuum from 16 to 18 inches, monitoring the diaphragm for smooth movement throughout the range. The EGR valve should maintain vacuum while applied. If it does not, the EGR valve needs to be replaced. If the diaphragm doesn’t move smoothly or return to the fully closed position, the EGR valve should be replaced.

vacuum test

Lack of Vacuum

While not common, it’s possible that the engine is not producing the necessary vacuum to operate the EGR solenoid. You can check this with a vacuum gauge. Disconnect the vacuum supply line to the EGR solenoid and install the vacuum gauge. Start the engine and monitor the vacuum. Vacuum should build around 17 to 21 inches when at idle.

If vacuum does not build into that range while at idle, there is a vacuum leak present that needs to be addressed. Search for a hissing noise in the engine compartment as a loose or damaged vacuum hose or connection is typically to blame. Repair the vacuum leak and confirm operation.

Common Causes of P0403

Defective EGR solenoid is most commonly found
Lack of electrical signal to solenoid, usually short to ground
EGR valve failure
EGR valve or passage restriction
Lack of vacuum, usually a vacuum leak
PCM short