Cylinder Head Dynamics

Cylinder Head Dynamics At Cylinder Head Dynamics, we specialise in precise CNC machining and high quality engine assembly

Coyote Gen 3 ready for assembly after we made the 3D cast flanged liners fitted then bore hone and decked on our CNC mac...
15/10/2024

Coyote Gen 3 ready for assembly after we made the 3D cast flanged liners fitted then bore hone and decked on our CNC machines
A lot of work but is very much needed in high horsepower for these engines
The factory spray on liner I didn’t measure but was only around .010” thick

16/12/2023

More CNC chamber softening on a pair of small block ford race heads

Sweet 1000+hp out the door, back to the sweet F6 falcon it belongs in to go fry some tyres 🤤
30/11/2023

Sweet 1000+hp out the door, back to the sweet F6 falcon it belongs in to go fry some tyres 🤤

TB48 Billet crank goodness!
14/11/2023

TB48 Billet crank goodness!

Complete head service on this LS head. It came in with smashed up pistons rings and ring lands that made a mess all over...
06/11/2023

Complete head service on this LS head. It came in with smashed up pistons rings and ring lands that made a mess all over the chamber.

With some clean up inside the chamber, new valve job and surface mill, only the low spots are left. We have saved this head from the bin and will perform once again.

Few Barra heads going through to be serviced at the moment. You can see the difference in exhaust seat profile, we use a...
03/11/2023

Few Barra heads going through to be serviced at the moment. You can see the difference in exhaust seat profile, we use a radius underneath the seat angle which provides superior flow. Also helped the case of sunken inserts with a top angle.

FJ20 Race port job, big flow increase on this head.
31/10/2023

FJ20 Race port job, big flow increase on this head.

Quick head recondition for this RB25. Performance multi angle valve job on intakes and radius for the exhausts, back-cut...
30/10/2023

Quick head recondition for this RB25. Performance multi angle valve job on intakes and radius for the exhausts, back-cut intake valves, aswell as reducing the effects of sunken valve seats with the final top angle.

CNC chamber soften on a nice set of Cleveland race heads. Ready for some serious boost ✅
26/10/2023

CNC chamber soften on a nice set of Cleveland race heads. Ready for some serious boost ✅

Roller thrust bearing on this Chevy crank was absolutely essential as one side of the thrust bearing was completely wipe...
25/10/2023

Roller thrust bearing on this Chevy crank was absolutely essential as one side of the thrust bearing was completely wiped out and even did damage to the crankshaft.

The crank has been saved as those surfaces will no longer be used with the roller thrust up the front.

Heap of LS heads getting serviced going through the shop at the moment. Multi angle valve job with blending into the thr...
24/09/2023

Heap of LS heads getting serviced going through the shop at the moment. Multi angle valve job with blending into the throat of the port makes for intense flow gains

RB26/30 bottom ends reconditioned ready to go. Acid bathed, pressure washed, bored, honed, decked, cranks linshed and fi...
22/09/2023

RB26/30 bottom ends reconditioned ready to go. Acid bathed, pressure washed, bored, honed, decked, cranks linshed and final hot chemical washed ready for assembly.

Address

Wyreema, QLD
4352

Opening Hours

Monday 7am - 4:30pm
Tuesday 7am - 4:30pm
Wednesday 7am - 4:30pm
Thursday 7am - 4:30pm
Friday 7am - 2pm

Website

Alerts

Be the first to know and let us send you an email when Cylinder Head Dynamics posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Cylinder Head Dynamics:

Shortcuts

Share

Category