John The Guard Roller

John The Guard Roller Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from John The Guard Roller, Automotive repair centre, Moorebank Avenue, Moorebank.

Guard work allowed this GT86 to airbag lower than before as the guard lip snagged the tyre..Front paint microns thicknes...
27/02/2026

Guard work allowed this GT86 to airbag lower than before as the guard lip snagged the tyre..

Front paint microns thickness measurement check @0.54mm and heat temp range monitored from 103-120 safe. Rear guards shaved for maximum wheel clearance for Work Meisters. Final outcome speaks for itself

For any guard work enquiries, contact on fb, instagram or 0406321081. Cheers

Nissan skyline r33 gtr. Tyre snag damage on the rears. Panel guard lip correction on the rears. Please send messages to ...
16/11/2025

Nissan skyline r33 gtr. Tyre snag damage on the rears. Panel guard lip correction on the rears.

Please send messages to 0406321081 for guard work.

Tuff Mitsubishi evo8mr. Shave work and rear bolt tab relocation. Paint thickness 0.35mm. Guards resealed and rust guar...
31/01/2025

Tuff Mitsubishi evo8mr. Shave work and rear bolt tab relocation. Paint thickness 0.35mm. Guards resealed and rust guarded.

For guard work enquiries 0406321081.

Mazda rx7 fd spirit R. front and rears rolled. paint micron thickness 0.76mm at 92° degree safe heat. car had some tyre ...
20/02/2024

Mazda rx7 fd spirit R. front and rears rolled. paint micron thickness 0.76mm at 92° degree safe heat. car had some tyre snag work that was corrected.

Mitsubishi Evo7 rear guard work and bolt tab relocation in preparation for new wheel set-up of 18x9.5 +22 offset
08/02/2024

Mitsubishi Evo7 rear guard work and bolt tab relocation in preparation for new wheel set-up of 18x9.5 +22 offset

Nissan Skyline R34. Rear guards paint microns thickness 0.65mm at 220°f safe heating range. Tuff jdm stance. For guard w...
18/12/2023

Nissan Skyline R34. Rear guards paint microns thickness 0.65mm at 220°f safe heating range. Tuff jdm stance.

For guard work, contact on 0406321081

Toyota Chaser Jzx100. Tuff stanced Chaser. Fronts guards were traditional handformed, crimped and tabs shaved. Rears sha...
07/12/2023

Toyota Chaser Jzx100.
Tuff stanced Chaser. Fronts guards were traditional handformed, crimped and tabs shaved. Rears shaved, rust guarded and resealed. A very delicate car to work on due to its panel design.

0406321081 for bookings or enquiries

Black on black Mitsubishi Evolution 8MR. Guards shaved and rear bolt relocation. For any guard work, contact on 04063210...
28/11/2023

Black on black Mitsubishi Evolution 8MR.
Guards shaved and rear bolt relocation.

For any guard work, contact on 0406321081

Holden commodore VE Clubsport. Paint thickness on fronts were 1.40mm at 210f degrees safe heat. Fronts were rolled using...
17/11/2023

Holden commodore VE Clubsport.
Paint thickness on fronts were 1.40mm at 210f degrees safe heat. Fronts were rolled using a 2 step process. Used the guard machine and then handformed and crimped to avoid paint cracking.

Mazda rx7 s8. Guards rolled. Paint micron thickness 0.80mm at 102° safe heating temps. For guard rolling work, please co...
24/10/2023

Mazda rx7 s8. Guards rolled. Paint micron thickness 0.80mm at 102° safe heating temps.

For guard rolling work, please contact 0406321081.

Nissan s15 1999 japspec widebody. Fibreglass guard shave work
02/04/2023

Nissan s15 1999 japspec widebody. Fibreglass guard shave work

Nissan 200sx S14 s2 guard roll front and rears. Paint micron thickness check. 0.62microns over 102c° safe heat temp. The...
20/10/2022

Nissan 200sx S14 s2 guard roll front and rears. Paint micron thickness check. 0.62microns over 102c° safe heat temp.

These paint micron checks are crucial before starting so make sure these are performed when quoting around. 0406321081

Address

Moorebank Avenue
Moorebank, NSW
2170

Telephone

+61406321081

Website

Alerts

Be the first to know and let us send you an email when John The Guard Roller posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to John The Guard Roller:

Shortcuts

Share

Category