Horder's Customs and Fabrication

Horder's Customs and Fabrication For all your automotive fabrication needs, from rollcages to intercooler piping, aluminium boat repairs, dog boxes and any other general fabrication and welding needs.

Send us a message for a free quote

Operating as usual

Injector rail modifications to fit an fg rail to a ba plenum. This is the intake for the same engine that got our custom...
28/08/2021

Injector rail modifications to fit an fg rail to a ba plenum. This is the intake for the same engine that got our custom turbo manifold fitted.

Another quad done for CQ Quad Spares and Sales. For any of your alloy, stainless or mild steel fabrication send us a mes...
25/08/2021

Another quad done for CQ Quad Spares and Sales. For any of your alloy, stainless or mild steel fabrication send us a message and see what we can do for you.

13b rotary manifold injection mods. When this one showed up another shop had already had a go at it. The injector bungs ...
19/08/2021

13b rotary manifold injection mods. When this one showed up another shop had already had a go at it. The injector bungs were just welded through into the runner square and blocking off a good chunk of flow inside. We removed the old bungs, changed the angle so they were aiming more towards the ports and corrected the spacing to allow the use of a standard rail. We also knocked up some stand-offs to secure the rail in place. For a repair job it turned out quite well.

3 inch stainless steel mandrel exhaust for an old hilux. All held together with vband clamps.
17/08/2021

3 inch stainless steel mandrel exhaust for an old hilux. All held together with vband clamps.

Another one out the door, its also coming back in next week for a full custom stainless exhaust aswell.
13/08/2021

Another one out the door, its also coming back in next week for a full custom stainless exhaust aswell.

Custom set of rockslider/brush bars for a cruiser. Nice and tight to the body but still really strong.
11/08/2021

Custom set of rockslider/brush bars for a cruiser. Nice and tight to the body but still really strong.

Probably one of the smallest intercooler pipes I've done. Colorado's usually have a rubber hose that keeps blowing out, ...
10/08/2021

Probably one of the smallest intercooler pipes I've done. Colorado's usually have a rubber hose that keeps blowing out, shouldn't have that problem any more.

Pair of custom brush bars fabricated for a hilux. The custom already had a set of sliders that were a little awkward to ...
21/07/2021

Pair of custom brush bars fabricated for a hilux. The custom already had a set of sliders that were a little awkward to meet up to, but pretty happy with how they turned out nice and tight to the body whilst still being sturdy.

Another front and rear alloy rack for CQ Quad Spares and Sales sometimes keeping it simple is the way to go.
17/07/2021

Another front and rear alloy rack for CQ Quad Spares and Sales sometimes keeping it simple is the way to go.

Custom barra manifold we fabricated, waste gate on and full coat of cerecoat. Down pipe and exhaust coming up soon.
23/06/2021

Custom barra manifold we fabricated, waste gate on and full coat of cerecoat. Down pipe and exhaust coming up soon.

Sometimes customers are after something simple to do the job. Here's a rooftop mount that will be heading to the Cape in...
17/06/2021

Sometimes customers are after something simple to do the job. Here's a rooftop mount that will be heading to the Cape in a few weeks. Im glad we could help them out and on their way.

Nice little ls torana in for a full exhaust. Full mandrel bent twin 2.5 inch to the diff with a H pipe and 2.25 inch out...
09/06/2021

Nice little ls torana in for a full exhaust. Full mandrel bent twin 2.5 inch to the diff with a H pipe and 2.25 inch out the back. The 9inch diff limited space but we still managed to thread it up and over. Nice cam which gives it an angry sounding idle. Painted black to match the style of the car. If you're after any performance exhaust work in stainless or mild steel, from mild to wild. Send us a message and see what we can do.

Little bit of a jigsaw puzzle with a lot of welding
07/06/2021

Little bit of a jigsaw puzzle with a lot of welding

A quad we had come in that had all the plastics destroyed. Started off doing just the rear deck and the job grew from th...
06/06/2021

A quad we had come in that had all the plastics destroyed. Started off doing just the rear deck and the job grew from there into a full job including front bar and a new seat frame fabricated. All made with tig welded aluminium coated in liner. Just have to freshen up the wheels. CQ Quad Spares and Sales

Even though we have been doing more performance and rust work, we're still getting some 4x4 jobs come through like these...
04/06/2021

Even though we have been doing more performance and rust work, we're still getting some 4x4 jobs come through like these side steps on a Pajero for better access. Send us a message if you're looking at getting any custom work done.

Sometimes people think they are saving money buy buying an eBay exhaust kit for their car. Sometimes they do, sometimes ...
30/05/2021

Sometimes people think they are saving money buy buying an eBay exhaust kit for their car. Sometimes they do, sometimes they have to spend alot more to get it modified to fit right like this one. As the old saying goes "buy once, cry once"

Its good to see the shop filling up and getting jobs out the door. We're on the final stretch with smiley's HK, we've go...
26/05/2021

Its good to see the shop filling up and getting jobs out the door. We're on the final stretch with smiley's HK, we've got a couple quads in for repairs and new guards. Also have a tough little cortina in for rust repairs and a pair of rotary Mazda's, one for exhaust work the other for a full build. We'll keep everyone updated as they progress.

13b headers and exhaust, headers are all mandrel bends and we fitted them to a customer's supplied RX7 exhaust that had ...
26/05/2021

13b headers and exhaust, headers are all mandrel bends and we fitted them to a customer's supplied RX7 exhaust that had to be modified to fit. Its was our first time working with rotaries, nice little engines with plenty of room.

Stainless steel 6into1 high mount barra manifold we've been working on, now the fun part, trying to weld it all up
12/05/2021

Stainless steel 6into1 high mount barra manifold we've been working on, now the fun part, trying to weld it all up

We don't just work on peoples toys, sometimes it's the little things we can do to make playing with your toys easier.
30/04/2021

We don't just work on peoples toys, sometimes it's the little things we can do to make playing with your toys easier.

Had a cruiser come in getting stone chips because the generic steps had gaps everywhere. We removed and replaced the tre...
29/04/2021

Had a cruiser come in getting stone chips because the generic steps had gaps everywhere. We removed and replaced the tread and fitted the new one to match the body. We added a couple extra stiffeners to harden it up a little aswell. Now its off for extreme liner for coating.

A burst panel we fitted to a big block blower manifold. I've welded alot of cast over the years and this was some of the...
07/04/2021

A burst panel we fitted to a big block blower manifold. I've welded alot of cast over the years and this was some of the worst, but we got the cast cleaned out and welded in the end.

Custom alloy intake we modified to clear the hood on a XA hardtop. Send us a message to see what we can do for all your ...
07/04/2021

Custom alloy intake we modified to clear the hood on a XA hardtop. Send us a message to see what we can do for all your automotive fabrication needs.

Custom alloy intake we modified to clear the hood on a XA hardtop. Send us a message to see what we can do for all your automotive fabrication needs.

Pacemakers tri-Y headers fitted into single 3inch stainless steel mandrel exhaust with a ho**er muffler. Turned out well...
06/04/2021

Pacemakers tri-Y headers fitted into single 3inch stainless steel mandrel exhaust with a ho**er muffler. Turned out well and even gave the stock motor a nice note.

Stainless steel intake pipe to finish off the hilux  intercooler piping upgrade.
02/04/2021

Stainless steel intake pipe to finish off the hilux intercooler piping upgrade.

Stainless steel intake pipe to finish off the hilux intercooler piping upgrade.

LS and T56 going into a Nissan Stagea. Full custom engine mounts and transmission mount fitted up nicely. The owner is g...
01/04/2021

LS and T56 going into a Nissan Stagea. Full custom engine mounts and transmission mount fitted up nicely. The owner is getting the engine rebuilt next then back in the shop for turbo manifolds.

Weve been pretty busy lately this is one of the jobs we've got out recently. Stainless steel front mount intercooler pip...
20/03/2021

Weve been pretty busy lately this is one of the jobs we've got out recently. Stainless steel front mount intercooler piping for a hilux. Its coming back in soon for a stainless intake aswell.

Custom set of rocksliders for a navara fabricated by us in collaboration with/finishing by Atwo 4x4. Coated in extreme l...
13/02/2021

Custom set of rocksliders for a navara fabricated by us in collaboration with/finishing by Atwo 4x4. Coated in extreme liner it came up a treat.

It has been a pretty busy week, we've got bikes, boats and 4x4s in the shed at the moment. This was a custom rear rack f...
12/02/2021

It has been a pretty busy week, we've got bikes, boats and 4x4s in the shed at the moment. This was a custom rear rack for
CQ Quad Spares and Sales send them a message for any spare parts or used quad sales.

Couple of repairs that have come through the shop over the past few days. Split aluminium cast bellhousing and a seat fr...
05/02/2021

Couple of repairs that have come through the shop over the past few days. Split aluminium cast bellhousing and a seat frame repair.

Had this John Goss in for a duel 3 inch stainless steel mandrel bent exhaust, took a bit to get it to fit over the diff ...
29/01/2021

Had this John Goss in for a duel 3 inch stainless steel mandrel bent exhaust, took a bit to get it to fit over the diff because it sat so low but got there in the end and turned out really well. The ho**er mufflers finished it off well. We are set up for all your stainless or aluminium intake or exhaust needs. We are taking bookings for late February and early march send us a message and see what we can do for you.

Customer needed somewhere to lock up fuels and consumables, we fabricated a lockable cage that can be configured to face...
28/01/2021

Customer needed somewhere to lock up fuels and consumables, we fabricated a lockable cage that can be configured to face forward or to the rear. We can do all sizes jobs in most metals, send us a message to see what we can help you with.

Long entry stainless steel snorkel we made for a isuzu dmax, these photos were before the welds were blended for a seaml...
21/01/2021

Long entry stainless steel snorkel we made for a isuzu dmax, these photos were before the welds were blended for a seamless look after its powder coated. Send us a message for any of your stainless welding needs.

Tyre carrier and quarter panel extensions. We can fabricate most types of bar work from brush bars and rock sliders to i...
19/01/2021

Tyre carrier and quarter panel extensions. We can fabricate most types of bar work from brush bars and rock sliders to internal and external rollcages. Now taking bookings for mid to late February.

We can make cages to any size needed, for around the house or the back of a ute. Steel or aluminium. Send us a message a...
19/01/2021

We can make cages to any size needed, for around the house or the back of a ute. Steel or aluminium. Send us a message and see what we can do for you.

Address

David Muir St
Mackay, QLD
4740

Telephone

+61451440481

Alerts

Be the first to know and let us send you an email when Horder's Customs and Fabrication posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Horder's Customs and Fabrication:

Nearby autos & automotive services


Other Automotives in Mackay

Show All

Comments

Big thanks to Tim for doing the exhausts on both of my falcons, Tim takes the time to ask what u want and how you want it done! Genuine great work and a genuine fella! 👍👍👍