SQ Engineering

19/12/2024

It been quite some time since an post was made on here so here are some product updates:

- The OEM replacement T50 sandwich plates are back in stock. These are 1.6mm thick zinc plated steel and are functionally the same as the factory part:
https://www.sq-engineering.com/product/ae86-ae71-t40-t50-gearbox-sandwich-plate/?v=3a1ed7090bfa

- The range of speedo drives available for the W5x / Supra gearboxes has expanded once again, now with 6 different models available:
https://www.sq-engineering.com/product/w5x-gearbox-speedo-drive/?v=3a1ed7090bfa

- 30mm Velocity stacks to suit 20V Blacktop throttles are back in stock, these can potentially suit the aftermarket airboxes from Noby-Booth and Mekaru:
https://www.sq-engineering.com/product/velocity-stacks-20v-4age-blacktop-throttles/?v=3a1ed7090bfa

14/05/2022

After a some delays, both variants of our 4A to J160 gearbox adapter kits are back in stock!

These kits are a direct bolt in solution and include everything needed; fasteners, sandwich plate and the custom thrust bearing carrier with thrust bearing pre-fitted.

Both kits are well proven and recommended products. The adapters are made out of 12mm thick steel plate for functionality and durability, anything thicker would push the gearbox too far back and cause the clutch spline to run off the input shaft. Steel was chosen as Aluminium would pose an unacceptably high risk of stripping the threads in the plate due to the limited thread engagement. These two factors are among the many different design aspects and features which were carefully chosen through our extensive design, test and revision process in order to provide the best possible solution on the market today!

Available for purchase via the SQ-Eng website:
https://www.sq-engineering.com/product/gearbox-adapter-kit-4age-7a-to-j160-g-1gfe/
https://www.sq-engineering.com/product/gearbox-adapter-kit-4age-7a-to-j160-s-3sge-beams/

All prices in $AUD, the shipping options and the prices can be seen during the checkout process before paying.

Pictured are the main adapter plates prior to when they had their locating dowels fitted.

14/06/2021

After a very long time one last batch has been manufactured of the adapter plates that allows for the airbox lid from a Nissan GTiR (SR20) to bolt up to 20V 4age throttle bodies. This is ideal for boosted 20V engines.

https://www.sq-engineering.com/product/20v-4age-intake-adapter-to-suit-nissan-gtir-plenum-chamber/

These are available to suit either of the 20V throttles. No airbox lids to suit are available for purchase, adapter plate only.

26/07/2020

Due to the supply and price issues with the genuine 3SGE Beams exhaust gaskets we now offer a heavy duty aftermarket alternative. These have a composite construction with dimpled steel / Armstrong style outer layers. The exhaust port openings have pressed steel firing rings for the highest resilience which are oversized to allow for those with enlarged exhaust ports. Lastly with a 1.8mm thickness these would have a higher tolerance for exhaust fl**ge variance / movement overall. Being custom made in a batch these are unique to SQ-Engineering and are currently available for purchase:

https://www.sq-engineering.com/product/3sge-beams-exhaust-gasket/

19/03/2020

For those who have been waiting the J160 relocation kits are once again available:
https://www.sq-engineering.com/product/j160-gearbox-shifter-relocation-kit/

Pictured are the housings that have finished being prepared with even more pending from the same batch.

11/11/2019

After a long delay a large batch of 20V 4AGE Blacktop Oil pumps are finally back in stock. These are genuine pumps from Aisin who are the OEM supplier to Toyota.

https://www.sq-engineering.com/product/20v-4age-blacktop-oil-pump-with-custom-options/

For those wishing to rev over 9000RPM TODA oil pump upgrade gears are also currently in stock but currently are listed as a separate product. The gears will be installed and the oil pump pre-packed & tensioned for free when both are purchased together:

https://www.sq-engineering.com/product/16-20v-4age-toda-oil-pump-upgrade-gears/

20v 4age Blacktop - Oil pump New and genuine oil pump intended for a 20V 4age Blacktop. Sold as is or with the additional options. All genuine pumps come with t

03/07/2019

Up until now the only 3SGE BEAMS workshop manual available was a not only in a very low quality but was quite short and hence missing many pieces of technical information.

Some time ago on our end an official full length hard copy manual was sourced and imported from Japan. This has been carefully scanned and edited to have a high quality. It covers the entire engine mechanical work / specifications across 61 pages. Although in Japanese its diagrams and specifications are easy to follow and if required translation software can be used.

As of now it is available free for everyone to download and share from our website via the link below. I figure this is well overdue and it should make it easier for those working on their engines.

https://www.sq-engineering.com/tech-articles/wiring-diagrams-and-diagnosis/

18/12/2018

It's been quite some time since our last post on here and there have been various changes happen in that time. One of those is the website that has been updated to use completely new and improved software.

As for parts updates after being out of stock for longer than they should of been the 4AGE Exhaust side alternator mounts have had they design updated and are now finally back:

https://www.sq-engineering.com/product/7a-4age-exhaust-side-alternator-bracket/

These have a 5mm step machined into the rear base to suit the OEM steel bracket on the rear wheel drive 4A engines (block to rubber mount). For others using a different arrangement a 5mm spacer is required which is available on request as an add on to the kit.

7A blocks don't have one of the block mounting points used by the tensioner arm base but if people want to make their own tensioner up we have the option of selling the main bracket by itself.

Lastly we are interested in anyone willing to share their own photos of the kit installed. If I like what's given and would like to use it on the website then a reward option is potentially there.

19/10/2017

All of our new J160 gearbox adapter parts are finally ready to go and are available for purchase through the website. It's taken a while to get everything exactly right, we wish to give thanks to those who have patiently waited.
- 4AGE / 7A to J160-G (1gfe):
http://www.sq-engineering.com/upgrade-parts/gearbox-gearbox-adapters/gearbox-adapter-kit-4age-7a-to-j160-g-1gfe.html
- 4AGE / 7A to J160-S (3S beams):
http://www.sq-engineering.com/upgrade-parts/gearbox-gearbox-adapters/gearbox-adapter-kit-4age-7a-to-j160-s-3sge-beams.html
- AE86 to J160 Gearbox mount:
http://www.sq-engineering.com/upgrade-parts/gearbox-gearbox-adapters/ae86-to-j160-gearbox-mount.html
- AE86 / AE71 / KE70 Engine crossmember spacers:
http://www.sq-engineering.com/upgrade-parts/gearbox-gearbox-adapters/ae86-ae71-ke70-engine-crossmember-spacers.html
For those buying anything off the website there is a bulk discount that automatically applies once the parts total is over $800 and the discount increases in intervals along with the total parts value from there.
The shipping options and prices are available before paying by adding the items to the cart and going to the checkout.
For those unsure which parts are required there is also a guide including a conversion parts check list here:
http://www.sq-engineering.com/index.php/tech-articles/j160-gearbox-conversion-guide

02/10/2017

Both of our 4AGE / 7A to J160 gearbox adapter kits are finally complete. All that's left to do before they are made available for purchase is putting together the product listings on the website.
The AE86 to J160 mounts have also been completed however the engine crossmember spacers are still at least a week away from completion.
These adapter kits will be released for $480 AUD each for either of the J160 variations (Beams or 1GFE). There will also be a +$60 AUD optional extra on the J160-G kit to relocate the clutch slave cylinder for additional exhaust clearance.

31/08/2017

Parts updates: Both of the 4A to J160 adapter plates are just about done. From here before the kits are complete there are still some smaller jobs that need to be finished such as some brackets and rods that need to be made, fastener packs put together, web pages made / updated, parts electro-plated and a few other odd jobs.
Pictured is the prototype AE86 to J160 gearbox crossmember, this was tested, it's design updated and a batch ordered. Originally a brace was going to be welded in but they were more than strong enough without one. These are due to be ready at the same time as the gearbox adapters and will be quite cheap.

24/07/2017

Parts Update: There is some more progress on both variants of the 4AGE to J160 gearbox adapters. The main adapter plate designs have been finalised, checked and sent off for production. The custom thrust bearing carriers and spigot extensions were sent to the machinist previously and are already underway.
While those parts are being made the other components will be organised such as the sandwich plates, fasteners and so on.
I wish to say thanks to those who have been patiently waiting on these. There will be more updates on here as they unfold.
Pictured are both variants, on the top is to suit the J160 originally from behind a 1GFE engine and the other on the bottom is for the gearbox that would normally bolt to a Beams engine.
No solid date or price yet