Online Bike Solution

Online Bike Solution Here you can find, All kinds of Motorcycle repairing, Engine Fitting, bike modification, spareparts.
(2)

31/05/2026

Loose Kick Problem? Clutch Adjustment Trick That Fixes It Fast

31/05/2026

Bike Brake Failed? Find Out the Real Problem Before It’s Too Late! 🛑

Motorcycle Carburetor: How It Works and the Role of the FloatThe carburetor is an important part of a motorcycle's fuel ...
31/05/2026

Motorcycle Carburetor: How It Works and the Role of the Float
The carburetor is an important part of a motorcycle's fuel system. Its job is to mix the correct amount of air and fuel before sending it into the engine for combustion. A properly working carburetor helps the bike start easily, idle smoothly, and deliver good performance and fuel economy.
How a Carburetor Works
Air enters through the air filter and flows into the carburetor.
As air passes through the narrow section called the venturi, it creates a low-pressure area.
This low pressure draws fuel from the carburetor bowl through jets.
The fuel mixes with the incoming air.
The air-fuel mixture then enters the engine cylinder, where it is compressed and ignited.
What Is the Float?
The float is a small component inside the carburetor's fuel bowl. It works like the float inside a water tank.
Its main job is to maintain the correct fuel level in the carburetor:
When the fuel level drops, the float moves down and opens the needle valve, allowing more fuel to enter.
When the fuel reaches the proper level, the float rises and closes the valve, stopping the fuel flow.
Common Float Problems
🔹 Float stuck open → Fuel overflow and leakage.
🔹 Float stuck closed → Engine starves for fuel and may not start.
🔹 Incorrect float height → Poor fuel economy, rough idling, and performance issues.
🔹 Damaged float needle → Fuel continuously enters the bowl, causing flooding.
Why Float Adjustment Is Important
A correctly adjusted float ensures: ✅ Proper fuel supply to the engine
✅ Smooth idling and acceleration
✅ Better fuel consumption
✅ Easy starting
✅ Prevention of fuel overflow
Regular carburetor cleaning and float inspection can prevent many common motorcycle starting and performance problems.

Do you know what causes a bike’s Chain sprocket set to wear out quickly? ⚙️🏍️No matter how good or expensive your gear s...
31/05/2026

Do you know what causes a bike’s Chain sprocket set to wear out quickly? ⚙️🏍️

No matter how good or expensive your gear set is 💸
if it is not maintained properly, it can get damaged quickly ❌

For example:
⛓️ Not tightening the chain on time
🛢️ Not lubricating the chain regularly
🛡️ Riding without a chain cover
⚠️ Ignoring regular maintenance

All these things can cause the gear set to wear out faster 😟
and then your bike may start making noise, giving jerks, and causing extra repair expenses 🔧💰

If you want your bike’s gear set to last longer 💯
make sure to regularly clean, lubricate, and maintain the chain properly ✅

A small precaution can save you from big expenses 🤝❤️

And don’t forget to share this post 🔄
so others can benefit too 🙌🏍️

One day, a customer brought a motorcycle to our workshop and was extremely worried. 😟The customer explained:👉 "The kick ...
31/05/2026

One day, a customer brought a motorcycle to our workshop and was extremely worried. 😟
The customer explained:
👉 "The kick starter has no resistance at all. When I try to kick-start the bike, I hear a chattering sound, but the engine won't start."
He also mentioned that: 🔹 Fuel supply was normal
🔹 Ignition current was present
🔹 The spark plug was in good condition
Despite all of this, the motorcycle still would not start properly.
It would occasionally start with a push, but as soon as the throttle was released, the engine would stall immediately. ⚠️
We carried out a complete inspection of the motorcycle. 🔍
The fuel system, ignition system, and most other components appeared to be functioning correctly. However, one issue became very clear:
👉 The engine was not producing proper compression.
At that point, we suspected that the problem was inside the cylinder head.
After removing and inspecting the cylinder head, the actual fault was revealed: 👇
❌ The exhaust valve was completely burnt.
❌ The intake valve and valve seat were heavily worn.
As a result: 🔹 Compression was leaking.
🔹 The kick starter felt weak and lacked resistance.
🔹 The motorcycle could not start or run properly.
To fix the problem, we: ✔ Installed new valves.
✔ Replaced the valve seals.
✔ Performed proper cylinder head fitting and gasket installation.
After reassembly and testing, Alhamdulillah: 👇
✅ Compression was fully restored.
✅ The kick starter regained proper resistance.
✅ The motorcycle started easily.
✅ The engine ran smoothly.
✅ The customer was very satisfied. 😊
Conclusion
Not every motorcycle fault is caused by fuel or ignition problems. ❌
Sometimes the real issue lies within the engine itself, such as valve damage, compression loss, or cylinder head defects. 🔧
Lesson Learned
A motorcycle problem cannot be diagnosed accurately without a thorough inspection.
A true mechanic is one who identifies the root cause of the fault rather than simply replacing parts. 🔥
🤲 May Allah ease everyone's difficulties, keep our journeys safe, and bless us with lawful and abundant sustenance. Ameen.
📌 Follow our page for more informative motorcycle repair tips and technical insights.
🔧 Share this post so others can benefit as well.

🏍️ Is Your Bike Starting to Smoke? Burning Oil? Don’t Rush to Spend Thousands! 😳Many riders get worried and think the en...
31/05/2026

🏍️ Is Your Bike Starting to Smoke? Burning Oil? Don’t Rush to Spend Thousands! 😳

Many riders get worried and think the entire engine needs a complete rebuild with huge expenses 💸

But friends, if your CD 70, 125, 150, or 200 has started smoking or consuming oil for the first time, it doesn’t always mean you need a full engine overhaul 🔧✨

✅ Cylinder is opened and inspected
✅ Head is being checked
✅ Piston rings are replaced
✅ Your bike can be restored at a much lower cost 🔥

If quality rings are installed properly:
✔️ Smoke can be greatly reduced
✔️ Oil consumption can decrease
✔️ Bike performance improves
✔️ And you can save thousands of rupees 💯

⚠️ The key is getting the job done by a skilled mechanic.

If you want me to explain the complete process:
🔧 How piston rings are checked
🔧 Which rings are best
🔧 Estimated cost of the repair
🔧 And how to keep your bike performing at its best for a long time

If you found this post helpful:
❤️ Like it
📲 Share it
💬 Leave a comment so others can benefit too.

😨 Why does a bike smoke?
🔧 Low-cost solution
🛠️ Piston ring replacement process
💨 Can oil consumption stop?
🔥 Restore powerful performance
💸 Save thousands of

30/05/2026

Bike Smoking & Oil From Silencer? Easy Fix!

30/05/2026

Bike mileage setting 1L 75kM

28/05/2026

Bike Runs After Pressing Clutch? Here’s the Real Problem! 😱

28/05/2026

Broken Brake Gutka replacement

Address

Al Ain
25000

Telephone

+971502193915

Website

Alerts

Be the first to know and let us send you an email when Online Bike Solution posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Online Bike Solution:

Shortcuts

Share

Category